lucid.page Milling, Turning, or Wire EDM? Walk the Geometry First
Text size
Read time5 min

# Milling, Turning, or Wire EDM? Walk the Geometry First

By Shelly

Contents

Affiliation note: I help the ProtoRFQ team with technical writing. The comparisons below are process-selection notes for common shapes, not a claim that any one route is reserved for a particular shop.

People often start an RFQ by naming a process: “this is a milling job,” or “send it to the wire room.” The more reliable order is the reverse. Look at the solid, name the features that actually have to be made, and only then ask which process can produce them in a sensible sequence. Three processes cover a large share of precision work — milling, turning, and wire EDM — and they overlap just enough for the wrong label to stick.

# Five shapes, and the question each one asks

A bushing with a flange and a cross-hole. The outside diameters, the bore, and the flange face are naturally turned. The cross-hole is a milling or drilling operation, often done in the same mill-turn setup or as a second operation. Calling the whole part a milling job usually means you will spend time indicating a cylinder in a vice that a chuck would have held more naturally. Call it turning with a milled feature, and say whether the cross-hole’s position is taken from the bore or from a flange flat.

A rectangular manifold with a few ports. This is milling territory: prismatic faces, drilled and tapped ports, perhaps a pocket. Turning is the wrong first thought unless a large circular register dominates the part. If a port runs into a pocket at an angle that a standard tool cannot reach, that is a workholding and tooling question inside milling, not a reason to change process family.

A thin through-slot in a hardened plate, 0.4 mm wide and 20 mm deep. A milling cutter that narrow will not like the depth, and the plate, if already hardened, may be past the point where carbide is a comfortable choice. Wire EDM is the process that can produce a narrow, deep, straight slot in the hard condition, provided you can accept a start hole or a tab, and provided the surface condition of the recast layer is acceptable or will be stoned or ground afterwards. Put those conditions on the drawing; do not leave them as shop folklore.

A shaft with a hex, a groove, and a tight bearing diameter. Turning owns the diameters and the groove. The hex can be milled or broached. The question is not “mill or turn the part?” but “which diameters are datums, and is the hex positioned from the bearing diameter?” A mill-turn machine can do both in one chucking, which is often the cleanest inspection story, because the same setup produces the relationship you care about.

A punch profile with sharp internal corners in tool steel. Internal corners sharper than a milling tool’s radius are a classic reason to go to wire EDM, especially if the blank is already hardened. If the corners can be opened to a tool radius, milling or grinding may be simpler. The drawing should say whether those corners are functional (a matching die, a sealing land) or just a modelled leftover.

# A short decision pass you can do on a print

  1. Circle every surface of revolution that shares an axis. If that set includes the datums or the tightest diameters, turning is in the route, even if other features are milled.
  2. Circle every prismatic pocket, face, or hole pattern. That set is milling, unless a hole is better made as a bored diameter on a lathe.
  3. Circle every feature that is thinner, sharper, deeper, or harder than a practical cutter will allow. That set is a candidate for wire EDM, or for grinding, or for a sequence (mill soft, heat treat, then wire or grind).
  4. Write the sequence in one line: for example, “turn soft, mill flats, heat treat, wire the slot, grind the datum face.” A reviewer can argue with a sequence; they cannot argue with a blank.

# What to send so the choice can be checked

The process label in an email is optional. The solid model, the current drawing, the material and its condition (annealed, pre-hard, treat after machining), and a note on which corners and slots are functional are not optional. If a feature can only be made by wire EDM, say whether a start hole is allowed and where, and whether the recast layer must be removed.

For a sense of how those routes are scoped when an RFQ is reviewed, ProtoRFQ publishes a CNC milling overview and a separate page for wire EDM work. Use them as a reminder of what each process is asked to confirm, not as a substitute for the geometry pass above.

The useful outcome of that pass is not a perfect process name. It is a package in which the hard features, the datums, and the material condition point to a sequence a reviewer can accept or challenge in writing.

End